How to Remove and also Replace a Bath Tub.
How to Remove and also Replace a Bath Tub.
Blog Article
They are making several great observations regarding How to Install a Bathtub as a whole in the content further down.
Setting up a bathtub isn't precisely rocket science, yet it does require strong plumbing, woodworking, and occasionally, tiling skills. Changing an old tub with a new one is additionally a moderately hard job. If the old tub is easily accessible, the task can move easily; if you have to open up a wall to get rid of the old tub and position the brand-new tub, the job is much harder. In either case, the job is within a residence handyman's skills, although you will certainly need an assistant to move out the old bathtub and embeded in the new one. Make certain you have certified on your own for the task and are comfortable trying it. Instead of working with a professional to take control of a halfway-completed project, it is far better to consider utilizing one before you begin. Opportunities are you may require a specialist plumber to make tube connections.
This write-up will assist you mount a new tub in your bathroom if you have currently acquired a new bathtub and also don't require to transform the arrangement of your previous supply of water pipelines.
Your tools as well as product list ought to make up the following:
Preparing for the Setup
To start with, the supporting frame provided with the bathroom must be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to ensure that if the tap includes a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be fitted in its last placement.
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you should do is separate the water. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather problematic due to the limited accessibility that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipelines. Once the supply pipes have actually been eliminated, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from turning throughout this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Before going on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Installing the Bath tub
Utilizing both wood boards under its feet, position the tub in the required placement. The wooden boards are helpful in uniformly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 little points.
The following goal is to make certain that the bathtub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the tub until the level reads degree.
To install faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Activate the supply of water and also inspect all joints and also new pipework for leakages and tighten them if needed. Fill the tub as well as also inspect the overflow outlet as well as the regular outlet for leakages.
Ultimately, repair the bathroom paneling as described in the maker's user's manual. Tiling and securing around the bath tub ought to wait till the bathtub has been made use of at least once as this will certainly settle it into its last placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and also the other end supplies a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin making certain that the washing machines are in location in between the faucet and also the sink. Safeguard the tap in place with the producer supplied backnut. As soon as the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal tap connectors. The former type must be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to split a stiff seal, causing the water to penetrate the wall between the bath and the tiling, leading to problems with dampness and possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your components and also installations. They are offered in tubes as well as cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked newspaper or soft rope. Remember to always fill the bath tub with water before sealing, to allow for the activity experienced when the bathtub remains in usage. The sealant can crack fairly very early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly available on the market. It is suggested to fit the floor tiles utilizing water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you liked our section on How to Install a Bathtub. Thank you for taking the time to browse our blog. Loved our entry? Please share it. Let other people discover it. I praise you for your time. Kindly come visit our site back soon.
Services Report this page